-
1 continuous circuit
Англо-русский словарь нормативно-технической терминологии > continuous circuit
-
2 continuous circuit
Холодильная техника: замкнутая схема, непрерывный цикл -
3 circuit
— ship-to-shore radio circuit— wire transmission circuit -
4 continuous current-carrying capacity
длительная пропускная способность по току
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва, 1999 г.]Тематики
- электротехника, основные понятия
EN
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Англо-русский словарь нормативно-технической терминологии > continuous current-carrying capacity
-
5 continuous current
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
непрерывный ток
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва, 1999]Тематики
- электротехника, основные понятия
EN
Англо-русский словарь нормативно-технической терминологии > continuous current
-
6 continuous-current circuit
цепь неизменного тока
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва, 1999 г.]Тематики
- электротехника, основные понятия
EN
Англо-русский словарь нормативно-технической терминологии > continuous-current circuit
-
7 continuous processing
-
8 continuous control
1. непрерывное регулированиеexchange control — валютный контроль; валютное регулирование
2. непрерывное управлениеEnglish-Russian big polytechnic dictionary > continuous control
-
9 continuous delivery rack
rack car — автовоз, платформа для перевозки автомобилей
English-Russian big polytechnic dictionary > continuous delivery rack
-
10 continuous running
running regime — режим работы; режим эксплуатации
English-Russian dictionary on nuclear energy > continuous running
-
11 continuous sampling sampling
непрерывный пробоотбор; метод непрерывного пробоотбора; непрерывный отбор проб; метод непрерывного отбора пробEnglish-Russian dictionary on nuclear energy > continuous sampling sampling
-
12 continuous waves circuit
Военный термин: линия телеграфной радиосвязи, радиотелеграфная сетьУниверсальный англо-русский словарь > continuous waves circuit
-
13 continuous wire circuit
Военный термин: непрерывно действующая линия проводной связиУниверсальный англо-русский словарь > continuous wire circuit
-
14 continuous-current circuit
Техника: цепь неизменного токаУниверсальный англо-русский словарь > continuous-current circuit
-
15 continuous waves circuit
линия телеграфной радиосвязи; радиотелеграфная сетьEnglish-Russian military dictionary > continuous waves circuit
-
16 continuous wire circuit
English-Russian military dictionary > continuous wire circuit
-
17 DC circuit
Англо-русский словарь нормативно-технической терминологии > DC circuit
-
18 direct current circuit
Англо-русский словарь нормативно-технической терминологии > direct current circuit
-
19 direct-current circuit
Англо-русский словарь нормативно-технической терминологии > direct-current circuit
-
20 supplying circuit breach
нарушение в питающей сети переменного тока
Любое изменение питания электрической энергией, которое может вызвать неправильные условия эксплуатации нагрузки.1)
[ ГОСТ 27699-88]
В МЭК 62040-3 определено 10 нарушений в питающей сети:
- Перерыв электропитания ( power outage) более 10 мс,
- Колебания напряжения ( voltage fluctuations) менее 16 мс,
- Voltage transients (4.16ms),
- Пониженное напряжение ( under-voltage) постоянно,
- Перенапряжение ( over-voltage) постоянно,
- Lightning effects (sporadic <1ms),
- Импульсные перенапряжения (voltage surges) менее 4 мс,
- Нестабильность частоты (frequency fluctuations) от случая к случаю,
- Voltage bursts (periodic),
- Искажение синусоидальности кривой напряжения (voltage harmonics) постоянно.
EN
power line disturbances
The ten most frequent disturbances (IEC 62040-3):- Power outage (>10ms),
- Voltage fluctuations (<16ms),
- Voltage transients (4.16ms),
- Under-voltage (continuous),
- Over-voltage (continuous),
- Lightning effects (sporadic <1ms),
- Voltage surges(<4ms),
- Frequency fluctuations (sporadic),
- Voltage bursts (periodic),
- Voltage harmonics(continuous).
[http://www.upsonnet.com/UPS-Glossary/]
1) Лучше - вызвать неправильную работу нагрузки
[Интент]Недопустимые, нерекомендуемые
- неисправность электропитания
- неполадки в электросети
- неполадки питающей энергосети
- перебои в сети
- сбой питания
- сбой электропитания
- сбой электросети
- сбой электроснабжения
Тематики
Синонимы
EN
Англо-русский словарь нормативно-технической терминологии > supplying circuit breach
См. также в других словарях:
Circuit switching — is a methodology of implementing a telecommunications network in which two network nodes establish a dedicated communications channel (circuit) through the network before the nodes may communicate. The circuit guarantees the full bandwidth of the … Wikipedia
Continuous simulation — refers to a computer model of a physical system that continuously tracks system response over time according to a set of equations typically involving differential equations.[1][2] Contents 1 History 2 Modern applications … Wikipedia
Circuit — Cir cuit, n. [F. circuit, fr. L. circuitus, fr. circuire or circumire to go around; circum around + ire to go.] 1. The act of moving or revolving around, or as in a circle or orbit; a revolution; as, the periodical circuit of the earth round the… … The Collaborative International Dictionary of English
Circuit court — Circuit Cir cuit, n. [F. circuit, fr. L. circuitus, fr. circuire or circumire to go around; circum around + ire to go.] 1. The act of moving or revolving around, or as in a circle or orbit; a revolution; as, the periodical circuit of the earth… … The Collaborative International Dictionary of English
Circuit of action — Circuit Cir cuit, n. [F. circuit, fr. L. circuitus, fr. circuire or circumire to go around; circum around + ire to go.] 1. The act of moving or revolving around, or as in a circle or orbit; a revolution; as, the periodical circuit of the earth… … The Collaborative International Dictionary of English
Circuit Showdown — Category Auto Racing Series Country or region Philippines Inaugural season 2010 Official website … Wikipedia
Continuous-repayment mortgage — Analogous to continuous compounding, a continuous annuity[1][2] is an ordinary annuity in which the payment interval is narrowed indefinitely. A (theoretical) continuous repayment mortgage is a mortgage loan paid by means of a continuous annuity … Wikipedia
Continuous Automatic Warning System — For the gun, see Heckler Koch HK CAWS. For the wrestling video game creation mode, see Create a wrestler. The Continuous Automatic Warning System (CAWS) is a form of cab signalling and train protection system used in Ireland to help train drivers … Wikipedia
Continuous wave — Passband modulation v · d · e Analog modulation AM · … Wikipedia
Circuit party — A circuit party in Atlanta, Georgia A circuit party is a large dance event, extending through a night and into the following day, almost always with a number of affiliated events in the days leading up to and following the main event. Circuit… … Wikipedia
Continuous Tone-Coded Squelch System — In telecommunications, Continuous Tone Coded Squelch System or CTCSS is a circuit that is used to reduce the annoyance of listening to other users on a shared two way radio communications channel. It is sometimes called tone squelch. Where more… … Wikipedia
